wdroge

i have a kyocera 2135 and the following socket card:
*
Hi-Speed DPC for Pocket PC's - Kyocera
Product Number: DP3091-378
*
Kyocera 2235, 2255 (Hi-Speed Phone) Data Burst up to 144 Kbps
Kyocera 2035, 2135, 3035 (Data Speed up to 14.4 Kbps)
************
i can access my earthlink dialup isp account perfectly every time (approx 25 times without any problems). using the 2135 and the socket dpc.
************
i can NOT access my verizon isp which is free with mobile office.
*
i have spent approx 4 hours with verizon tech support - techs could not find anything wrong with my configuration.
*
i have left socket messages in both email/voice. socket has only responded in email. socket has not provided any solutions. the 2135 and the dpc are supposed to be compatible with verizons 14.4kb isp connection. the software provided with the dpc provides a wizard for verizon express network (144kb) and verizon qnc (14.4kb). the verizon qnc wizard was not successful for me.

socket communication has provided very little support in this matter. any suggestions would be greatly appreciated.

thanks for your help.

boatride

look up the .pdf for verizon at this link

http://www.supplynetwireless.com/drivers.cfm

the .pdf shows how to set your phone and pda to work on both the express and standard network.

If you have a KWC 2135 phone it is Express Network Capable..

To access the 144k you must be in a express network area or it will fall back to 14k


hope it helps

wdroge

thanks to ImARollingStone and BoatRide, I have been able to successfully connect to Verizon Qnc (14.4) and Earthlink Dialup.

Below are the properties I used. You may be able to tweak these properites a little more, however, I know these attributes will work. I tried to format the best I could.

thanks again.

***********
Pocket Pc Dialup Access

1. Dialing Locations (same for Verizon and Earthlink):
Start, settings, connections, dialing locations
Location = Socket Wireless
Tone dialing = check
Country code = 1
Dialing patterns
Local calls = G
Long distance calls = G
International calls = G


2. Verizon Access:
a. Verify that Verizon has changed your account to access mobile
office (14.4)
b. Connections:
Start, settings, connections, internect connections
New (DPC QNC 0115 – name I chose for connection)
Select a modem = Socket HS DPC Card
Baud rate = 19200
Advanced
Port settings
Data bits = 8
Parity = none
Stop bits = 1
Flow control = none
Use terminal before connecting = check
Tcp/ip
Use server assigned ip address = check
Use ip header compression = check
Name servers
Use server-assigned addresses = check
Next
Country code = 1
Area code = 913 (this is the area
code assigned to my phone)
Phone number = #777
Next
Cancel call if not connected within 120 seconds
= check
Extra dial-string modem commands = &C2

3. Earthlink Access:
a. Verify that Verizon has changed your account to access
mobile office (14.4)
b. Connections:
Start, settings, connections, internect connections
New (Std Data Earthlink – name I chose for connection)
Select a modem = Socket HS DPC Card
Baud rate = 19200
Advanced
Port settings
Data bits = 8
Parity = none
Stop bits = 1
Flow control = none
Use terminal before connecting = do NOT
check
Tcp/ip
Use server assigned ip address = check
Use ip header compression = check
Name servers
Use server-assigned addresses = check
Next
Country code = 1
Area code = 913 (this is the area code
assigned to my phone)
Phone number = 6802881 (this is a local
earthlink access number)
Next
Cancel call if not connected within 120
seconds = check
Extra dial-string modem commands = blank
(nothing is keyed in)