Just got my new axim X51v through on friday - had already ordered the innopocket case. Case is really nice but the supplied charging connector doesn't fit through the hole cut in the bottom of the case :realmad:
Anyone else have this problem? Am I going to have the same problem with all the connectors that fit into the bottom of my axim?(was thinking of getting a VGA out connector as well.....)
I have the same problem with the x50v. The dell-provided connector does not fit, as you have observed. However, I have some third-party accessories (travel charger, battery extender etc.)and the connectors on these fit without any problem. Sanding down the dell-connector may help, but haven't tried it myself.
i have this case and the dell cable and it fits on mine. I had to make sure the x50 was all the way in though. It fits better over time. Make sure you push it in the case fairly hard to get it all the way in.
"Always vote for principle, though you may vote alone, and you may cherish the sweetest reflection that your vote is never lost." -- John Quincy Adams
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. and To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. and To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. and To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
... Make sure you push it in the case fairly hard to get it all the way in.
I have pushed the Ax in the case until it will go no further. Despite this, the connector does not fit. Sometimes it will go in and supply power, but the connector does not click into place,so even a gentle pull on the connector will dislodge it. If only the connector can go in less than a mm, I think it will click into place.
"Always vote for principle, though you may vote alone, and you may cherish the sweetest reflection that your vote is never lost." -- John Quincy Adams
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. and To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. and To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. and To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Connector fits perfect on mine. Actually after a few weeks the lower black foam begins to take on the shape of the corners of the axim. So not to worry too much if it dosn't fit quite yet. On one of the pictures, I circled where you could cut into the plastic very lightly and the connector should fit fine after that. An Xacto knife works well with plastic.
I have three connectors (home, work, and car) and all needed to be shaved down with an Xacto knife, but it just takes a minute or so. Or you could take a Dremel tool to the case.
Just got my new axim X51v through on friday - had already ordered the innopocket case. Case is really nice but the supplied charging connector doesn't fit through the hole cut in the bottom of the case :realmad:
Anyone else have this problem? Am I going to have the same problem with all the connectors that fit into the bottom of my axim?(was thinking of getting a VGA out connector as well.....)
I would not recommend shaving your case, I would modify the cable only. First off its easier, secondly its hard to make the case look good after you've grinded the slot.
Where did you guys get your Innopocket Mag case I have looked everywhere on the net and everybody is out!!! I purchased a Kursell Leather but don't like the thickness or the Snap Strap and will send back to cases.com if they will return for credit/cash.
__________________
Axim X50v A04
Windows Mobile 2003 SE (Ditched the buggy Windows Mobile 5)
Inno Magenisum Case:approve:
Sandisk SD 1Gb
Sandisk CF 1 Gb
Brando Scrn Protector
Holux GR-230 BT GPS :approve:
Moto HS810 BT HeadSet
Copilot 5 Live Nav Software To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts. (POS don't buy, now trying iNav:) & Mapopolis:approve: )
2 Standard Batteries (rat's lost one) To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
AudioVox SMT5600 AT&T & 256Mb SD
Wants
CF Infrared Card
Memory-Map Nav Software
VGA Cable
Where did you guys get your Innopocket Mag case I have looked everywhere on the net and everybody is out!!! I purchased a Kursell Leather but don't like the thickness or the Snap Strap and will send back to cases.com if they will return for credit/cash.
Ordered direct from innopocket and received it last week - even though their website shows out of stock. Like the case a lot. About to go and shave the connector down with a stanley knife....
(Never heard of an exacto knife guess that's a US thing?)
Follow Us
RSS Feed
Follow on Twitter
Facebook
YouTube
Addicted Member
