X50V pin layout?

[siepe]

...so, what's up... nobody can't tell me the x50v pin out? I don't belive it

[BKF]

So, no sound output eh?

I don't believe the bottom connector outputs sound, does it?

Otherwise wouldn't the Seidio Car Mount cradle output sound without having to connect to the headphone jack? Or does it do this without the cable? Their pictures are a little misleading.

[dlweston]

Follow this link and they make a cable for connecting a serial GPS to the X50 http://www.yourmobiledesk.com/produ...D=2003&mfrID=na.

[Swim100flyy]

The Link doesnt work, dlweston

[yoda16]

can somebody ssend me the pinout

[skimask]

The Link doesnt work, dlweston

It's at www.yourmobile.com
Part Number is SN-19000S (those are zero's not O's)

[Tai_Tony]

The pin# 4 & 11 is not identified in X50v side. Please confirm it.

i got this information from NickM_ (thanks!). it can be obtained from any official VGA cable, i don't see any reason why not to make it public.

----------------------------
No hardware at all.
Pin out (preliminary)

Pin# x50v Label Function
1 33 RED Red color signal
2 35 GREEN Green color signal
3 31 BLUE Blue color signal
4 ID2 Monitor identification bit 2
5 N.C. Not Connected
6 34 GND-RED Ground Red signal
7 36 GND-GREEN Ground Green signal
8 32 GND-BLUE Ground Blue signal
9 N.C. Not Connected
10 30 GND-SYNC Ground Sync signal
11 ID1 Monitor identification bit 1
12 26 ID0 Monitor identification bit 0
13 28 H-SYNC Horizontal Synchronization
14 29 V-SYNC Vertical Synchronization
15 N.C. Not connected

[Tai_Tony]

Can anybody send me the pin-out of X50v ? I need it to connect my GPS.

[Tai_Tony]

Please PM me or send E-mail to me.

tony@go-china.net

Check your message box :)

[iwantanaxim]

I would also be interested in the complete pin-out. Can someone PM it to me. Thanks!!!

I dont think anyone has a full pinout yet, but if they do please post it :)

[biohzrd]

Has there been any progress on the pinout over the weekend?

I have found on the Haicom website a diagram showing what pins go to where on the GPS PS/2 cable coming from the receiver , SO I know that end, just need to know where to solder them to on the x50v connector!

Haicom Diagrams

It's only 4 pins to solder! This would be cake if only we knew what pins were RX and what pins ere TX.

from what we currently know about the VGA cable :

i got this information from NickM_ (thanks!). it can be obtained from any official VGA cable, i don't see any reason why not to make it public.

----------------------------
No hardware at all.
Pin out (preliminary)

Pin# x50v Label Function
1 33 RED Red color signal
2 35 GREEN Green color signal
3 31 BLUE Blue color signal
4 ID2 Monitor identification bit 2
5 N.C. Not Connected
6 34 GND-RED Ground Red signal
7 36 GND-GREEN Ground Green signal
8 32 GND-BLUE Ground Blue signal
9 N.C. Not Connected
10 30 GND-SYNC Ground Sync signal
11 ID1 Monitor identification bit 1
12 26 ID0 Monitor identification bit 0
13 28 H-SYNC Horizontal Synchronization
14 29 V-SYNC Vertical Synchronization
15 N.C. Not connected

Pins 30,32,34,36 all seem to be ground. So Pin 1 from the gps PS/2 can go to any of these.

Pin 2 on GPS PS/2 is VCC (i'm guessing to charge the unit via PS/2?)

We need which pins on axim connector are TX, RX, and VCC.

If anyone has ANY further info or corrections on what we have so far PLEASE post or PM me if afraid to post it!

[biohzrd]

*bump*... anyone have any new info?

[NickM_]

This pin out is not tested (first of all odd and even pins order).
X50V uses TTL serial interface (3.3 v).

DTR 14
DSR 13
TX 11
RX 10
RTS 9
CTS 8

[biohzrd]

Those are numbered how? Based on what schematic of the pins?

This one?

             back of x50v 
  ______----________________________----______
  |  1               17   19               35|
  | _-_-_-_-_-_-_-_-_-    _-_-_-_-_-_-_-_-_- |
  | 2               18   20               36 |
  -------------------_____--------------------
             front of x50v